top of page
Poppy Shop Logo

DREAMSTATE BRACELET

  • Writer: N/A
    N/A
  • Jan 27, 2021
  • 1 min read


ONLINE CROCHET PATTERN: A combination of leather work (or faux leather) and crochet combine to make a fun, easy and quick to make up bracelet. Options to use fingering, lace or metallic thread for this unique yet simple pattern.

SIZES: XS-XL Includes templates for sizes xs-xl (wrist sizes ranging from 5.5-8 inches in circumference).


SKILL LEVEL: Moderate


HOOK: 2.5mm or hook size that produces tight weave and does not cause fabric to pucker. YARN: Approximately 20 yards of fingering or lace weight yarn or 1mm metallic thread.


EXTRAS:

  • Leather or faux leather fabric)

  • tool for punching holes in leather/fabric (see pattern notes)

  • scissors

  • stitch markers

  • fabric clips

  • printer

  • tapestry needle.


ree


PATTERN NOTES

Pattern Notes:

  • This pattern includes templates and instructions for bracelet sizes xs-xl.

  • Sizes are shown in parenthesis as follows xs (s, m, l, xl).

  • You will require a tool for punching holes in the leather/fabric. You may choose to use either and awl or a leather hole punch. The hole size should measure approximately 2mm.

  • Sample photos are of a size small bracelet.

  • If the number comes before the abbreviation, for example: 2hdc, this means stitch the given number into the same stitch. If the number is given afterward, for example: hdc2, this means to half double crochet the given number over subsequent stitches.

  • The right side (RS) and wrong side (WS) of the project are indicated in the far left table column of the stitch instructions.

  • Fasten off and weave in all ends when you are finished.

  • Slip stitch to join rounds.

ABBREVIATIONS

ch Chain

slst Slip stitch

hk Hook

st Stitches

s-slst Surface slip stitch

hdc Half double crochet

slst Slip stitch

WS Wrong side

RS Right side

TEMPLATE

DOWNLOAD THE PATTERN TEMPLATE



(WS) Print out the template for your chosen bracelet size (last page of this document) and cut it out. Make sure to measure the 5 centimeter box once the page is printed, to make sure your printer settings are correct and that your bracelet will turn out the correct size. With the wrong side of your fabric/leather facing you and trace around the edge of the template. Cut out around the traced line (with scissors or a razor knife) and then clip the template in place to the right side of your fabric. Punch the stitch holes out using either an awl or 2mm leather hole punch.

*The punched hole should measure approximately 2mm.


ree

ree


STITCH INSTRUCTIONS

R1: (RS) Pull up your yarn in the end most hole of the bracelet & ch1, 3hdc, 3hdc in each hole across until 1 hole remains unworked, 6hdc in the last unworked hole, rotate so you are now working into the other side of the bracelet, 3hdc in each hole across, join into the very first st.

*You will need to pull each stitch up to working height.

84 (90, 96, 102, 108)


ree

ree

ree

ree

R2: (RS) Ch1, slst1 into each st around, join.

84 (90, 96, 102, 108)


ree

R3: (RS) s-slst across the center of the bracelet. Fasten off, weave in all ends.

14 (15, 16, 17, 18)



ree

(RS) Attach a lobster clasp with a jump ring through the outer edge stitches to one end of the bracelet and a single jump ring to the other end of the bracelet.


ree

ree

FINISHING

Weave in all ends.


CONGRATULATIONS YOU ARE FINISHED!

SHARE YOUR WORK AND TAG


@POPPYSHOP.CA & #DREAMSTATEBRACELET



WANT THE PRINTABLE VERSION OF THIS PATTERN?






bottom of page